If you wish to contribute or participate in the discussions about articles you are invited to join SKYbrary as a registered user
Aircraft Load and Trim
From SKYbrary Wiki
Revision as of 12:25, 28 December 2017 by Editor1
|Content control:||Air Pilots|
|Tag(s)|| Overrun on Take Off,|
Overrun on Landing
- 1 Description
- 2 Loading Procedures
- 3 Fuel Loading and Distribution
- 4 Load and Trim Sheets
- 5 Departure Control Systems (DCS)
- 6 Manual Load Sheets
- 7 Aircraft Commanders' Acceptance of Load and Trim Sheets
- 8 Electronic Flight Bag generation of Load and Trim data
- 9 Provisional and Final Load Sheets
- 10 Risks arising from aircraft loading
- 11 Consequences of actual misloading or incorrect input of load-related data
- 12 Accidents and Incidents
- 13 Related Articles
- 14 Further Reading
It is a legal requirement and crucial to the safety and structural integrity of an aircraft that it is loaded in such a way that the specified maximum allowable weights are not exceeded and that the centre of gravity as loaded will be within the permitted flight envelope and remain so for the entirety of the intended operation. Once these conditions have been satisfied, it is equally crucial that the flight crew are aware of the prevailing weight and centre of gravity so that they can set aircraft equipments appropriately; these include take off reference speeds, slat/flap position, and pitch trim or stabiliser position. This is important to ensure that the aircraft will achieve published certified performance and that the aircraft retains expected stability and control characteristics. It is also very important that aircraft baggage and freight load complies with the restrictions on carriage of dangerous goods.
It is essential that the Dispatcher, or other official assigned responsibility for overseeing aircraft loading, specifies the loading requirement correctly and has a reliable method by which he/she can be satisfied that his/her instructions have been carried out as requested. Whilst modern automated systems may determine the seating options for passengers and the load disposition, effective procedures and compliance remain the only way of ensuring that what has been specified and passed to the aircraft commander has actually been achieved. Specification of the hold compartment loading is usually achieved by the completion of a Loading Instruction Form (LIF). The LIF is given to the loading supervisor who certifies that it has been complied with and returns it to the issuer as evidence that the work has been completed. The completed load and trim sheet are then given to the aircraft commander. The human supervisor must also have a reliable means of confirming that if dangerous goods are loaded the dangerous goods regulations are complied with and a Notification to Captain (NOTOC) is issued and duly signed by the aircraft commander. The original NOTOC is retained by the aircraft commander onboard and a copy is held at the departure point. The human supervisor must also confirm that any special requirements for securing unusual items in the holds or in the passenger cabin have been complied with.
Fuel Loading and Distribution
Many swept wing jet transport aircraft use fuel distribution to optimize the centre of gravity in cruise to reduce fuel burn. This is achieved by keeping the C of G towards the aft limits of the envelope by utilizing outboard wing, aft body or horizontal stabilizer fuel tanks. It is the aircraft commander’s responsibility to ensure that the fuel load prior to takeoff is correctly distributed and reflected on the load/trim sheet and maintained within the prescribed limits for the remainder of the flight.
Load and Trim Sheets
The traditional method for ensuring load and trim compliance dates from the days when all load and trim sheets were completed manually on specific forms designed for use with each aircraft type, and is as follows:
- the completed document is presented to the aircraft commander
- the aircraft commander checks that it is internally consistent by carrying out some simple cross checks of input and calculated output data for gross errors and,
- if the cross checks are satisfactory, the commander formally accepts the load and trim sheet by means of a signature on at least two copies, one being retained by the departure agent and the other by the flight crew.
The DCS (Departure Control Systems) process is slightly different in that only the input data need be checked and the completed document may not necessarily be signed by the agent presenting it, as he/she may have had no part in its preparation.
However, in both cases, the acceptance of an apparently correct load and trim sheet does not guarantee that the aircraft has necessarily been loaded as stated.
Departure Control Systems (DCS)
Most Load and Trim Sheets used today in commercial air transport operations by multi-crew aircraft are produced by contracted Handling Agents who input flight-specific data into a proprietary DCS. There are a number of commercial DCS products available. Some are operated by large airlines for their own use and then also employed to generate external user business. Other similar DCS are operated independently of any particular airline. Where DCS are used, the data input and electronic generation of the load and trim sheet may be carried out at a regional centre and merely printed off, together with corresponding LIF, by the aircraft operator or the contracted handling agent employees. Note that DCS will only produce output data as accurate as the inputs, so it is important to guard against input errors.
Manual Load Sheets
Manual Load sheets involve a pro forma calculation of Maximum Ramp Weight (MRW), Maximum Take Off Weight (MTOW) and Maximum Landing Weight (MLW) whilst the centre of gravity is located by marking the requisite aircraft operating weight (vertical scale) on a ‘drop line’ located on a centre of gravity ‘index’ scale which forms the horizontal axis. If the position so found is within the areas shown as the permitted safe flight envelope, (and remains within the safe area as fuel reduces to planned landing weight) then operation as loaded is possible. Manual preparation of load and trim sheets used to be commonplace but they are now used so infrequently that recalling the necessary method can be challenging to ground staff and flight crew alike. Many younger pilots have seldom or never prepared a manual load and trim sheet or checked one for acceptance; this unfamiliarity significantly increases the risk of undetected errors with significant consequences. It is good practice to complete a manual load sheet once a month to develop and sustain proficiency against the day one suddenly becomes essential at short notice.
Aircraft Commanders' Acceptance of Load and Trim Sheets
The aircraft commander must be given a copy of the completed load and trim sheet for the flight and should check and sign it, leaving a copy at the point of departure. The aircraft commander is obliged to accept that the aircraft is loaded as stated in respect of the Hold Loading. However, in respect of Passenger Cabin Loading the senior cabin crew member usually confirms the number of passengers actually on board by means of a headcount after boarding has been completed.
Electronic Flight Bag generation of Load and Trim data
For some flights, especially but not only cargo flights, the flight crew have an electronic flight bag (EFB) which they use to calculate aircraft performance data, which takes account of the completed load and trim sheet. They also use the EFB to make the load and trim calculations themselves, so that once it has been checked, all that is required is that a copy be left with the agent at the point of departure. Clearly, it is vital that a rigorous process of crosschecking is included in the preparation of such documentation to avoid input errors. Crosschecking does not mean simply repeating the numbers selected/presented but also confirming that they make sense in relation to the actual situation.
Provisional and Final Load Sheets
DCS and the communication facility afforded by ACARS (aircraft Communicaitons Addressing and Reporting System) has allowed aircraft commanders to be given substantially complete and correct loading documents with ‘provisional’ status in plenty of time before STD; ‘final’ status documents with highlighted minor amendments (also known as Last Minute Changes - LMC) can be generated as the aircraft leaves the gate for acceptance via ACARS at any time before take-off commences.
Adjustment of the Last Minute Changes (LMC)
It is often necessary to adjust the loadsheet after completion. These adjustments are called last minute changes (LMC). The LMC process is a way to enter late alterations/updates to a final manual or electronically produced loadsheet, without requiring revisions to the main body or the preparation of a new document. Guidance material on the LMC is made available by UK CAA: CAP 1008 Last minute changes (LMC).
Any LMC increase or change must not exceed the:
- allowable underload calculation (Underload is the weight that still is available until the first limiting maximum weight is reached).
- maximum mass and balance limits for zero fuel, take-off or landing
- limitation of any compartment that is intended to be used
There is a maximum allowable change to the number of passengers or hold load as an LMC, which will be specified in the individual operator’s Operations Manual for each aircraft type. Operators must also specify a similar rule for changes to the balance condition, to be defined in index units. If there are changes to fuel quantities and/or locations, the weight and balance figures should be fully recalculated and new documentation produced because of the significance in terms of the aircraft mass and balance condition. However, some operators may permit fuel LMCs for lesser quantities, so fuel mass and index data must be made available and should be checked.
If any LMC occurs after the completion of the mass and balance documentation, it must be brought to the attention of the captain and clearly entered on the documentation. The captain should amend the mass and balance sheet, but it is essential that it is recorded on the copy kept at the point of departure.
Risks arising from aircraft loading
The primary risks arise from the aircraft being ‘set up’ for take off with incorrect pitch, trim and/or take off reference speeds. This can arise in one of three ways:
- The aircraft is not loaded in the way stated on the accepted load and trim sheet (applicable to any load sheet type)
- The aircraft load and trim sheet uses correct input data but the output data is wrong (applicable to manual load sheets)
- The flight crew apply the (correct) load and trim data incorrectly when using it to calculate aircraft take-off performance data, including reference speeds and scheduled thrust settings.
- The hold load is not properly secured or contains prohibited or incorrectly packed items.
Either actual miss-loading of an aircraft or incorrect use of correct load related data for aircraft systems set up can severely affect aircraft performance, stability and control. Loss of Control may occur during an attempted take off or during subsequent flight because either:
- an attempt (usually inadvertent) is being made to operate the aircraft outside the AFM limits, or
- flight crew actions to control the aircraft are ineffective because the aircraft is unable to achieve the expected performance, whether in relation to manually selected or FMS generated safety speeds on the ASI(e.g Vr) or selected engine thrust parameters.
One potential consequence of an error in loading or data entry is tailstrike on take off. This will usually lead to fuel dumping and a return to the take-off airfield, without pressurizing the cabin and is not career enhancing for any of the pilots, even the relief crew. Even more serious, Runway Excursion has been a regular result of errors of both these types in the past, whether or not an RTO has been attempted. Given the potential severity of a mistake in loading, of transferring erroneous weight and balance figures however derived, of entering erroneous data into the aircraft management systems (FMS) or miss-setting ASI speed bugs, both pilots should always carry out Gross Error checks. Seniority does not imbue data entry infallibility! Amongst other checks, it is vital to confirm that the Zero Fuel Weight is sensible and then that the indicated Take-Off Weight is as expected.
For a more detailed discussion of the issues arising with hold and cabin loading, see Hold Loading and Passenger Cabin Loading which also have links to reports of investigations into specific outcomes consequent upon hold or cabin loading data being incorrectly calculated or applied.
Accidents and Incidents
The following events involved aircraft loading as a factor:
- A306, Paris CDG France, 1997 (On 30 July 1997, an Airbus A300-600 being operated by Emirates Airline was departing on a scheduled passenger flight from Paris Charles de Gaulle in daylight when, as the aircraft was accelerating at 40 kts during the take off roll, it pitched up and its tail touched the ground violently. The crew abandoned the takeoff and returned to the parking area. The tail of the aircraft was damaged due to the impact with the runway when the plane pitched up.)
- A332, Sydney Australia 2009 (On 4 July 2009, an Airbus A332 being operated by Jetstar Airways on a scheduled passenger flight from Sydney to Melbourne carried a 750 kg ULD which had been expressly rejected by the aircraft commander during the loading operation without flight crew awareness. There was no reported effect on aircraft handling during the flight.)
- AT76, Dublin Ireland, 2015 (On 23 July 2015, an ATR72-600 crew suspected their aircraft was unduly tail heavy in flight. After the flight they found that all passenger baggage had been loaded in the aft hold whereas the loadsheet indicated that it was all in the forward hold. The Investigation found that the person responsible for hold loading as specified had failed do so and that this failure had not been detected by the supervising Dispatcher who had certified the loadsheet presented to the aircraft Captain. Similar loading errors, albeit all corrected prior to flight, were found by the Operator to be not uncommon.)
- AT76, en route, west-southwest of Sydney Australia, 2014 (On 20 February 2014, an ATR 72-600 crew mishandled their response to an intended airspeed adjustment whilst using VS mode during descent to Sydney and an upset involving opposite control inputs from the pilots caused an elevator disconnect. The senior cabin attendant sustained serious injury. After recovery of control, the flight was completed without further event. Post flight inspection did not discover damage to the aircraft which exceeded limit and ultimate loads on the stabilisers and the aircraft remained in service for a further five days until it was grounded for replacement of both horizontal and vertical stabilisers.)
- B190, vicinity Charlotte NC USA, 2003 (On 8 January 2003, a B190, operated by Air Midwest, crashed shortly after take off from Charlotte, NC, USA, following loss of pitch control during takeoff. The accident was attributed to incorrect rigging of the elevator control system compounded by the airplane being outside load and balance limitations.)
- … further results
- Loading of Aircraft Holds
- Passenger Cabin Loading
- Use of Erroneous Parameters at Take-Off
- Limit Load
- European Action Plan for the Prevention of Runway Excursions Edition 1.0, January 2013.
- Takeoff Weight Entry Error and Fatigue (OGHFA SE)
- Analysis of aircraft weight and balance related safety occurrences - NLR, 2007
- Take-off performance calculation and entry errors: A global perspective
- UK CAA CAP 1008 Last minute changes (LMC) - Guidance document, February 2014
- UK CAA CAP 1009 Gross error checks - Guidance document, February 2014
- UK CAA CAP 1010 Ramp/ Aircraft Loading Operations Checklist, February 2014